A smart home is a pretty cool idea right? While you are out to dinner you can check on your children at home and make sure the baby sitter is behaving. Or you heard a cold snap is coming tonight so you adjust the thermostat so your home will be toasty when you get there. It is the dream, right? I agree, it is a lot of fun.
The only problem is with the upcoming roll out of 5G technology, manufactures are pushing more for doing everything wireless, than they did before. The technology is amazing but WiFi radiation causes cancer. WiFi emits microwave, also known as, Radio Frequency (RF) Radiation. If you go to the “Scientific Studies” page of this website, I link to some of the hundreds of peer reviewed studies that link RF Radiation to things like cancer, DNA damage, (especially in infants), crib death and infertility. Even the World Health Organization classifies it as a possible “carcinogenic”, which means “cancer causing”.
The RF Radiation used by these devices is microwave radiation. This is the same radiation that your microwave oven uses to cook food. In the video below is a British Physicist named Barrie Trower. In his early career he was trained by the Royal Navy to be an expert in microwave radiation, especially as it applied in military weapons.
Then he spent the rest of his career as a professor specializing in microwave radiation. He is an expert on how harmful this radiation is. The below video is very much worth watching. He explains how microwave radiation causes cancer, crib death and DNA damage.
Wired Smart Homes Safer
Smart homes can be designed to connect to each device in the system via wires, rather than wireless. About the only thing that needs to be wireless might be your cellphone & tablets. And in other articles on this site I show you some very simple ways to protect yourself from cellphone radiation.
Smart systems can communicate over the negative wires in the electrical wiring, or via computer cables wired through the home. It just depends how they set the system up. Some features would have to communicate via computer cables. In this article we are going to discuss the different parts of a smart home, the RF Radiation that it emits, and what alternative wired devices could be used instead.
(Note: Just remember even wired smart devices cause RF Radiation in the home in the form of Dirty Electricity. But Dirty Electricity is more easily protected against that RF Radiation being emitted by wireless devices. You can simply plug in a Graham-Stetzer Filter into an electrical outlet on those circuits. Because of this ability wired smart devices are by far the safest way to design a smart system.)
How A Smart Home Works
A smart home means that you you can control and/or automate all or many of the electrical devices in your home from a central control panel or from a computer, tablet or smartphone.
A simple way to think about a smart home is you basically set up a computer network in your home. The network is run by a central controller that connects to each electronic device in your home. And in a smart home more things are electronic, such as light switches, than in a typical home.
Then this central controller controls turning on and controlling all of the electrical devices attached to it. Software is installed with a simple control dashboard or panel so the home owner can automate or manually control each of these devices in a very simple and convenient way. This dashboard exists on a central control panel in the home, as well as by a home computer, tablet and smart phone.
Smart Home Components
Okay now let’s look at each part of a basic smart home, and talk about what is the safest ways are to do the different things smart homes are designed to do. We already spoke a bit about the brains of the system, the controller.
A controller is basically a computer that can be set up to communicate with each of the devices. Since this is a computer it is connected to the internet. This device itself is not wireless, unless a wireless feature is added to it, so it does not emit RF Radiation.
A security system is something that is very often included as part of a smart home. Everything in a security system can be hard wired. What I am talking about here is sensors and video cameras. Some people think of a smart deadbolt as part of a security system, also though it is not. It is a smart item, and part of a wireless smart system, but not part of the security system
A security system is to ring an alarm when someone is attempting to break in, and to film the interior and/or exterior of the home. Motion sensors are infrared and detect heat, and do not give off RF Radiation. So again you can have a completely hard wired security system connected to your controller.
WiFi thermostats are all the rage of late. The problem is they emit a ton of RF Radiation. They are one of the higher RF Radiation emitting devices you can have in your home. And there really is no need for them. A standard digital thermostat can be set to have different temperatures at different times of the day. Some even have vacation modes that you can set when you leave town, and for a specific number of days.
Also many heating and air conditioning companies recommend that you not change your temperature too often. They say that it can cause spikes in your heating bill and is not good for the system. They recommend to set your temperature on a schedule with a digital system and forget about it. Let it run on its schedule.
Intercoms And Cameras
We talked a bit about cameras earlier in the security system section of this article. Intercoms and cameras all can be hard wired. There is no reason for them to be wireless. I have even seen aftermarket wired intercom and camera systems that can be installed in different rooms in the home, with no need for WiFi whatsoever. And they were relatively easy to install and looked very professional.
This can also be done to create a baby monitoring system so that you don’t need a baby monitor. The wireless baby monitors emit worse levels of RF Radiation than even a WiFi thermostat. Anything you can do to avoid a microwave emitting device blasting your baby is worth the money and effort. They are so dangerous.
Centralized Lighting System
In a smart home one of the most RF Radiation emitting things you can include are smart light bulbs. I would say just don’t do it. They are wireless with either WiFi or Bluetooth. And they emit a lot of RF Radiation. They are bad news. And there is no way to get a metal mesh shield to protect yourself from the RF Radiation. And if you could figure out a way it would look tacky.
Many smart light bulbs also create massive amounts of Dirty Electricity on your electrical circuits. And in rooms that have a lot of these light bulbs, a filter by itself is sometimes not enough to lower the emissions down to safe levels.
And you do not even really need smart light bulbs. Smart light switches will do everything that your smart light bulbs will do, and they can be hard wired instead of WiFi or Bluetooth. So then all you need is a Graham-Stetzer Filter to reduce the Dirty Electricity they cause down to safe levels.
The idea behind smart appliances is that you can control them remotely from your central control dashboard, computer, tablet or smartphone. And a smart appliance will communicate with your home network and tell you things like when your clothes dry cycle is done. This allows you to start, stop and check on the appliance remotely.
The problem is that the push is to connect all of these appliances to your network via Bluetooth or WiFi. If you do then basically every electronic device in your home, from your blender to your sprinkler system control box, would emit significant amounts of RF Radiation.
Your whole house would be bathing in RF Radiation at high levels. Most manufactures of smart devices give you both the option of controlling them by WiFi or Bluetooth, or plugging your appliance directly into your smart network via an Ethernet cable. The Ethernet cable is the way you want to go. Then you will want to go into your appliance settings and turn off the Bluetooth or WiFi.
If you are setting up your home as a smart home, the best rule of thumb is to hard wire everything. If it cannot be connected through wiring, then I would not have it as part of my smart system. Then you can have all of the convenience and fun of having a smart home, without exposing your family to the carcinogenic RF Radiation.
Reducing RF Radiation In Your Home
Besides being careful not to have any part of your smart network WiFi emitting, it is important to go through the rest of your house and test to see if any devices you already have are emitting RF Radiation.
Some obvious examples of things you may have that will be would be things such as smart meters (electric, gas and water), a cordless phone, baby monitor, and a WiFi router. I filmed myself going room by room through a home testing for devices like that, then I describe how I would fix each RF Radiation problem I found. You can watch these videos on the “How To Test For RF Radiation” page on this website.
I will show just one of these videos here in this article. This below video shows me testing how much RF Radiation is emitted by my 5 GHz WiFi router. Then I put the router into a device called a “WiFi Router Guard” which is a steel mesh box that blocks 90% to 95% of the RF Radiation emitted from the router. And the amazing part is my WiFi still works. This video is definitely worth watching. I highly recommend it.
Reducing The Dirty Electricity In Your Home
By creating a smart home you will by the very nature of it create a bunch of Dirty Electricity in many of the circuits in your home. If you have a smart meter on your home you will have a bunch of Dirty Electricity on every circuit of your home just from that.
Like I said earlier in this article it is much better to design a smart home where everything is hard wired in, even though it creates Dirty Electricity, because you can reduce that. Having your whole home filled with WiFi or Bluetooth emitting devices is much harder to protect against. You can’t stick your WiFi thermostat in a WiFi Router Guard for example to protect you from the RF Radiation.
But with Dirty Electricity unless the circuit has an electrical wiring problem such as a grounding issue, you should be able to reduce the Dirty Electricity by installing a Graham-Stetzer Filter in the circuit.
In the below video I test a circuit in my kitchen that reads a little bit over the safety level, and then I correct it by inserting a filter and test it again. In the video you can see how much it reduced the problem. Again this video is short but very much worth watching. I highly recommend it.
I guess the two main points I am hoping people get out of this article is 1. that RF Radiation has extensive scientific studies done on it and it really is very harmful, and 2. we can still have our neat gadgets, and even a smart home, if we just think it through and make good decisions in the process. I hope this video is helpful and benefits you.
Related article: How To Protect Yourself From RF or EMF Radiation